Last Updated on July 21, 2023 by asifa
So, your Netgear router is flashing red. But, before you decide to discard your WiFi device and buy a new one, walk through this post. Here, we will provide you with a number of hacks to get rid of the Netgear router red light issue in a matter of minutes. So, let’s take the plunge.
Fixed: Netgear Router Red Light Issue
Note: Prior to troubleshooting the Netgear router red light issue, ensure that you have successfully set up your WiFi device using the 192.168.1.0 IP address.
Reboot the Netgear Router
Let’s start fixing the red light issue with the most ancient hack i.e. rebooting. The rebooting process is one of the most proven methods to resolve various issues related to the Netgear router. And, who knows, it will also rid you of the router red light issue.
Here are the instructions that will help you reboot the Netgear router:
- Disconnect your Netgear wireless router from the modem.
- Press the Power button to switch off your wireless router.
- Unplug the router from its respective wall outlet.
- Done? Good. Now, let your Netgear router stay idle for some time.
- Plug the wireless router back into the power outlet.
- Press the Power button to turn on the router.
- Connect the router to the modem.
Once your Netgear router gets rebooted, check whether it is flashing red or not. If you are still running out of luck, don’t wait to implement the next hack.
Connect Your WiFi Devices Properly
Perhaps, the connection between your Netgear and modem is loose due to which you are facing the red light issue. So, consider strengthening the connection between your WiFi devices. If there is a wireless connection between them, then ensure that they are within range of each other.
If you’ve used an Ethernet cable to connect them, check that it is damage-free. In case the Ethernet cable has cuts, get it replaced with a new one.
Relocate Your Router
After installing the wireless router using the 192.168.1.1 IP address, users are advised to change its location. But, it looks like you have selected an improper location for your Netgear WiFi router. Therefore, without any delay, consider relocating it and placing it in a WiFi interference-free zone.
The WiFi interference-free zone is the one that lacks the presence of devices emitting radio wave frequencies. To name a few, don’t place the router near cellular phones, televisions, refrigerators, microwaves, treadmills, baby monitors, Bluetooth speakers, etc. Besides, metal objects can also deviate the router’s WiFi signals. So, don’t place your router close to metal objects, mirrors, and fish tanks.
Don’t Let the Router Overheat
Chances are that your Netgear router is flashing red due to overheating. Being a networking device, it is normal for the router to produce heat, but overheating is dangerous. Therefore, place your router in a well-ventilated room so that the heat can be dissipated properly.
Apart from that, dust off the dirt on your Netgear wireless router and switch it off when not in use. If doing so also fails to resolve the red light issue for you, then your router might be operating on an outdated firmware.
Perform Netgear Firmware Update
Performing Netgear router firmware update can also help you get rid of the red light issue. Just in case you are unaware of the firmware update process, walk through the below-mentioned guidelines:
- Connect your router to the modem.
- Switch on your PC.
- Launch a web browser of your choice.
- Go to the URL bar.
- Type the 192.168.1.2 IP address.
- Press the Enter key.
- Use the router’s default login credentials to reach the Netgear Genie dashboard.
- Once you reach there, click Settings > Maintenance > Firmware Update.
- The firmware of your wireless router will get updated in a couple of minutes.
That’s how you can update your Netgear WiFi router.
Reset and Reconfigure
If nothing has worked in your favor till now, then there is a high possibility that your router is partially configured. Therefore, you need to configure it properly. Before that, reset your WiFi device.
The router can be restored to the factory default mode by a single push of the Reset button. Once you do that, set up the router from scratch using the 10.0.0.1 IP address.
Final Thoughts
This was all about how to fix the Netgear router red light issue. We hope that the troubleshooting tactics mentioned in this post will help you in resolving the red light issue with ease.
Read More: How to Activate Netgear Armor Subscription Feature?